Versions BricsCAD (Mac)

Nouveautés

• Commande ARRIERE-PLANOuvre la boite de dialogue ARRIERE-PLAN et applique les paramètres d'arrière-plan choisis à la vue (modèle) actuelle.
• BIMPATCH
  • Note : pour activer BIMPATCH, le paramètre 'GENERATEASSOCVIEWS' doit être activé avant la génération ou mise à jour de BIMCOUPE sur laquelle un BIMPATCH sera créé. Le paramètre est actif par défaut lorsque l'on choisit le profil BIM profile dans la boite de dialogue Démarrage, à partir de la V17.2. Lors de la mise à jour d'une BIMCOUPE, le traitement peut nécessiter des modifications du modèle 3D ou de tout autre modèle référencé, afin de fournir une associativité entre le modèle 3D et les dessins 2D. Dans ce cas, une approbation des modifications est demandée dans la ligne de commande. Répondez 'Oui' si vous souhaitez utiliser BIMPATCH.
  • BIMPATCH, exécutée dans l'espace modèle d'un dessin créé par BIMMAJCOUPE, permet de spécifier une zone rectangulaire superposée au résultat de BIMCOUPE.
  • En utilisant EDITREF vous pouvez maintenant modifier le résultat de la coupe dans la zone rectangulaire, en modifiant ou en ajoutant des détails.
  • Lorsque la coupe BIM correspondante est mise à jour, BricsCAD vérifie si le résultat de la coupe générée dans ce rectangle est identique au résultat généré au moment où le patch BIM a été créé.
    • Si ce n'est pas le cas, les modifications sont préservées, mais le contour est colorié en rouge.
    • Sinon la modification du patch effectuée par l'utilisateur est conservée.
    • Les points d'intersection et les extrémités des courbes provenant des objets 3D sont utilisés pour trouver la position du rectangle du patch. Lorsque les objets sont modifiés ou déplacés dans le modèle 3D, de telle sorte que la position de ces points d'intersection change, mais la géométrie à l'intérieur du rectangle patch n'est pas affectée, alors BricsCAD déplacera les patches modifiés par l'utilisateur.
  • Le contour rectangulaire créé par BIMPATCH est placé sur le calque BIMPATCH_BOUNDARY.
• SYSTÈMES DE RÉFÉRENCE DE COORDONNÉES Ajout des systèmes de référence de coordonnées polonais suivants :
  • EPSG:2176: ETRS89 / Pologne CS2000 zone 5
  • EPSG:2177: ETRS89 / Pologne CS2000 zone 6
  • EPSG:2178: ETRS89 / Pologne CS2000 zone 7
  • EPSG:2179: ETRS89 / Pologne CS2000 zone 8
  • EPSG:2180 (Pologne CS92)
  
  SR73094SR73257
• Commande COUPURECOTE Coupe une cote et ses lignes d'extension à l'endroit où elles croisent d'autres entités.
  SR32362SR40993SR66140SR71512
• Variable système DMAUDITLEVEL Contrôle si certains types d'erreurs sont retournés ou non par la commande DMAUDIT. Si elle est égale à 1 alors la plage d'erreurs du noyau de modélisation est ignorée.
• PROPRIÉTÉS GÉOMÉTRIQUES
  • Pente Fournit l'angle entre une entité et le plan XY, c'est-à-dire le plan horizontal du SCU courant. Cet angle est calculé à partir de la normale de l'entité.
  • Élévation minimum et maximum dans le SCU Retourne la valeur minimale et maximale de la coordonnée Z d'une entité dans le SCU courant.
  • Ces nouvelles propriétés géométriques sont disponibles dans le panneau de Propriétés, le panneau Structure, les infobulles et Extractdonnees.
• Variable système LAYERFILTEREXCESS Lors de l'ouverture d'un dessin qui contient plus de filtres de calques que la valeur LAYERFILTEREXCESS, et si le nombre de filtres de calques excède le nombre de calques, une boite de dialogue s'affiche et recommande de supprimer tous les filtres de calques afin d'améliorer la performance. Si LayerFilterExcess vaut 0, le dialogue n'apparaît pas. Le dialogue LayerFilterExcess n'est pas affiché pour des dessins ouverts avec l'API COM.
  SR69632SR72949
• PANNEAU DE PROPRIÉTÉSAjout de nouvelles propriétés : Pente, MinZ, MaxZ.
• Boite de dialogue PROXYINFO Affiche des informations à propos des entités proxy contenues dans le dessin courant.
• PROXYNOTICEAffiche une information à l'ouverture d'un dessin contenant des entités personnalisées créées par une application qui n'est pas présente.
  SR70994SR71012SR71024
• CONFIGURATION QUAD La personnalisation du Quad a été retravaillée afin de la rendre plus flexible et plus facile à gérer.
  • Les noms des éléments Quad sont maintenant moins abstraits.
    • L'ancien élément Quad est maintenant un bouton Quad : chaque outil est affiché comme bouton dans un onglet Quad.
    • L'ancien groupe Quad Group est maintenant appelé onglet Quad : c'est en fait une collection de boutons Quad affichés dans un onglet.
    • L'ancien Alias a été renommé en Filtre Objet : il définit les types d'objets pour lesquels un bouton Quad s'affichera.
  • Les actions de configuration se font soit
    • en utilisant glisser-déposer
    • u en utilisant le menu contextuel par clic-droit.
  • La boite de dialogue Personnalisation (ouverte par la commande Personnaliser) comporter deux sections :
    • La section Quad
      Dans cette section, le nom et le contenu de tous les onglets Quad peuvent être spécifiés, de manière identique à la personnalisation des onglets du ruban. Les onglets Quad peuvent être créés, copiés, renommés et supprimés. Gérez le contenu d'un onglet Quad en faisant glisser les boutons depuis le côté droit de la boite de dialogue, ou en utilisant le menu contextuel par clic-droit pour ajouter, renommer, déplacer ou supprimer les boutons Quad. Le côté droit du dialogue contient la liste complète de tous les boutons qui peuvent être affichés dans le Quad. Cela inclut les outils définis dans le fichier cui, ainsi que tous les boutons Quad définis en interne, listés sous la nouvelle branche 'Interne'. Ces boutons intégrés sont similaires aux outils, sans possibilité de modifier leur nom, icone, chaîne de commande, etc..., qui sont en lecture seule. La condition permettant de spécifier si un certain bouton Quad apparaîtra quand le curseur survole une entité, est spécifiées pour chaque bouton individuellement dans la propriété 'Filtre objet', de manière identique à la configuration des éléments du menu contextuel Objet. Il n'est pas possible de modifier le Filtre Objet d'un bouton Quad intégré.
    • La section Espaces de travail
      Cette section définit quels onglets seront disponibles dans le Quad, dans quel ordre, et dans quel espace de travail. Dans cette interface, l'utilisateur peut ajouter/déplacer/supprimer des onglets Quad. Le contenu des onglets Quad n'est ni affiché, ni modifiable dans cette section, comme cela se fait actuellement dans la section 'Quad' du dialogue. Quand un nouvel onglet Quad est créé dans la section Quad, celui-ci est automatiquement ajouté dans tous les espaces de travail.
• Commande RECUPERERTOUT Récupère un dessin ainsi que toutes les références externes imbriquées, chaque dessin est sauvegardé avec une copie .BAK et un rapport .ADT.
  SR73535
• Paramètre RedHilite_DUCSLocked_Face_Color Contrôle la couleur de surbrillance pour la face sur laquelle le SCU Dynamique a été verrouillé (en appuyant sur la touche Maj).
• Paramètre RedHilite_DUCSLocked_Face_Alpha Contrôle la transparence de la face sur laquelle le SCU Dynamique a été verrouillé (en appuyant sur la touche Maj).
• Variable système RUBBERBANDCOLOR Contrôle la couleur d'affichage du ruban élastique par exemple dans les opérations de déplacement.
  SR73894
• Variable système RUBBERBANDSTYLE Contrôle le style d'affichage du ruban élastique - 0 = solide 1 = pointillé.
  SR73894
• Paramètre SHADEDGEContrôle le résultat produit par la commande OMBRAGE
  • Shadedge = 0 -> style visuel = Gouraud
  • Shadedge = 1 -> style visuel = Gouraud avec arêtes
  • Shadedge = 2 -> style visuel = Caché
  • Shadedge = 3 -> style visuel = Plat avec arêtes
• TÔLERIE
  • Commande TOLGRAVER  sépare les faces épaisses de pièces de tôlerie en gravant des arêtes, selon les rebords et plis adjacents.
  • Commande TOLPARAMETRER  ajoute automatiquement des contraintes 3D à une pièce de tôlerie afin de contrôler ses dimensions.
• TEXTEDITMODEVariable système qui contrôle la répétition automatique de la commande d'édition de texte DDEDIT.
  
  
  • 0: Mode édition multiple (répétition de la commande jusqu'à annulation) (valeur par défaut)
  • 1: Mode édition unique (la commmande se termine après édition d'une unique entité texte)
  • 2: Mode édition automatique (mode unique si le texte est présélectionné, sinon mode multiple)
  
  SR75364
• VUESAjout du support de la rotation de vues délimitées ou non.
  SR66177
• Commande EXTRACTFACES Extrait un jeu de faces de solides ou surfaces 3D en tant que nouvel objet surface 3D.

Improvements

• DCL
  • Improvements for small screens or large dcl dialogs:
  • • On Linux and Mac, use a slightly smaller font in dcl dialogs. Dcl dialogs ended up somewhat bigger on Linux and Mac compared to Windows.
    • Allow reducing the size of dialogs that exceed a size of 800x600. If a dialog is wider than 800 pixels, an end user can now resize it to a smaller width down to 800 pixels. Likewise, dialogs can be reduced in height down to 600 pixels. Reducing the size of a dialog below minimum size does not change the layout of the dialog, instead the contents will become only partially visible and scrollbars appear to control what part of the dialog is visible.
  SR75938
• GENERATED VIEWS Performance of certain steps (such as preview generation and processing external .dwg files) of VIEWBASE, VIEWSECTION or VIEWDETAIL commands has been improved.

• 3D CONSTRAINTS .bak files are created now when external .dwg files are modified upon constraints creation.
  SR72209
• ATTRIBUTESImproved ATTSYNC and BATTMAN dialogs reordering of attributes containing fields.
  SR67236
• BIMSECTIONUPDATETo support working in other units than mm or inch, hatch scale factors are now multiplied by a factor depending on INSUNITS to have the same result when working in cm, m, feet, ..
  SR73605SR74373
• BMREPLACEThe new Type option allows to choose whether the new component maintains the link to its definition file or not.
• BMUPDATE
  • The command now accepts a selection set of component instances or features faces. Corresponding objects are updated.
  • Command no longer updates generated drawing views when issued in Model Space. In Paper Space, the command updates only selected views or all views in case the "Entire model" option is used.
• BIMSECTION result layers 2D Result geometry is now placed on layers corresponding with the material names of the compositions used by the 3d solids. The sectionplane settings define a layer for Intersection Boundary, Intersection Fill or Background lines. Corresponding 2d geometry is placed on these layers. When these layers contain the keyword '*EntityLayer*', BricsCAD BIM substitutes this keyword by the the name of the material defined by the composition attached to the BIM object. The default BIMSECTION settings now include this keyword.
• DIMENSION EXPLORERThe 'DIMBREAK gap size' property has been added.
• DIRECT MODELING
  • DMRECOGNIZE system variable
    • This system variable, which controls the automatic design intent recognition, is now stored per-document and saved in the .dwg file to allow predictable behaviour of parametric components.
    • New design intent options "Vertices between 4 or more faces" and "Edges between coincident faces" have been added as bitflags of DMRECOGNIZE. Both these flags are disabled by default which means that default behaviour of direct modelling commands has been changed in newly created documents and the documents created previously, but not containing any 3D constraints.
  • DMTHICKEN command can now be applied to regions.
• ERASE The command now erases imprinted edges of 3D solid objects.
• ETRANSMITUnsaved document changes no longer block ETRANSMIT, a warning is triggered instead.
• FIELDSIncreased performance of fields update in a drawing with thousands of fields.
  SR74626
• FIND AND REPLACE dialog
  • Following shortcut keys were introduced: Alt+R for Replace, Alt+A for Replace All and Alt+F for Find.
  • Added search option "Current Layout"
  
  SR71618
• FONTSImproved stability in case invalid SHP/SHX font files are used. This is achieved by substituting invalid fonts automatically with the font specified by the FONTALT setting.
  SR71796SR74353
• GETTING STARTED dialogThe width of the dialog was made resizeable.
• GRIPS system variableExtended to allow separate control of the display of midpoint grips on polyline segments.
  The type of the GRIPS system variable has been changed from boolean to integer.
  SR71783
• GUIWhen no drawing is loaded, the ribbon, the toolbars and all menus except the File menu are disabled.
  SR73497
• HIGHLIGHT PERFORMANCEImproved speed of rendering highlighted lines by a factor 5 for the default 2d display device (GDI+).
  SR73976
• IFC IMPORT
  • Following improvements were made:
  • • Improved performance and decreased memory usage when importing IFC files.
    • Fixed a bug in IfcArbitratryProfileDefWithVoids
      SR74692
    • Import site, building, and building storey properties
    • Fixed a bug when the same IFC model was imported multiple times
    • IFC material information is now imported to the project library.
    • Properties from IFC common property sets are now imported as BIM properties.
    • IFC spatial structure is imported, including site, building and story information.
    • Composed elements from IFC are imported as classified (nested) named blocks.
    • Added logging for import of not supported IfcProduct.
    • Apply correct material layer set usage from IfcSlab. The reference major surface is set according to the extrusion direction of the IfcSlab.
    • Compose new name from material layers if MaterialLayerSet name is empty.
    • If more than one IfcRelAssociatesMaterial is found, the material layer set (usage) is imported first.
    • Entities with multiple geometric representation items can be imported as blocks.
      SR74371
• IMAGES IN RENDERED VISUAL STYLE
  • When a rendered visual style is used...
  • • Regen speed has vastly improved.
    • The display of bitonal images has been improved.
    • Huge images containing billions of pixels can now be displayed.
    • Image settings like fade, contrast, brightness are supported now.
• IMPORT Hidden assembly parts are now imported as hidden entities also in case EXPORTPRODUCTSTRUCTURE is set to Off.
  SR70570
• JOINSupports preselection of entities now.
  SR69727
• LAYERSTATEWhen creating a new layer state, the 'Layer Properties to restore' of the layerstate that is currently selected are used for the newly created one.
  SR75057
• LEGACY HIDDENLINE PERFORMANCEStrongly improved legacy hiddenline calculation performance for drawings containing clusters of dense geometry at large coordinates.
  SR73534
• MATERIALS COMBOThe Materials combo used in the Layers Panel and the Layer Explorer is now sorted in a case-insensitive way.
  
• MECHANICAL BROWSER
  • Added more detailed diagnostic messages in case errors are found in an assembly. E.g. for cases when some parametric components could not be recalculated or component definition files are lost.
  • Added the possibility to localize an external component nested in a local one.
• MTEXT dialogMText dialog now uses large icons on ultra-high resolution screens.
• MULTI-THREADING 3 new flags to control parallel processing were added to the MTFLAGS variable
  • Flag 8 controls parallelized calculation of hidden line removal. Hidden line removal is used by operations like Flatshot, SectionPlaneToBlock, BimSection generation, Drawing View generation.
  • Flag 16 controls parallelized calculation of BimSections to separate destination drawings.
  • Flag 32 controls parallelized calculation of BimSections to a single destination drawing.
• PERFORMANCEStrongy reduced the time required to create a new drawing using QNEW in case the TEMPLATEPATH points to a heavy folder hierarchy. Similar improvement for opening the Print dialog in case PLOTCFGPATH or PLOTSTYLEPATH point to a heavy folder hierarchy.
• PREVIEWPreview functionality has been added for the PrintAsPdf BricsCAD printer driver. A preview PDF file is generated (in the system Temp folder) and opened with the application registered for viewing PDF files.
  SR74187SR75205
• PRINT AS PDF Added dedicated custom paper size name edit control.
  SR73243
• PROJECTIONTYPE setting The default value is set according to the MEASUREMENT setting. For the Imperial system third-angle projection type is used, for the Metric system first-angle projection is used.
• PROPERTIES PANEL Xref drawings are now reported as 'External Reference' to distinguish them from block inserts.
• PUBLISH dialog
  • Publish options are now retained when publishing from Sheet Set panel.
    SR75278
  • Reworked dialog to provide direct access to Publish to Pdf settings.
  • Publish to PDF no longer uses the 'PDF export' settings, the dialog now uses its own settings stored and retrieved from registry and dsd files.
  • Simplified and unified hatch type and dpi settings for publishing to pdf.
  • Now the Page Setup choice list is reopened after 'Import...' was chosen, so one can see the imported Page Setups immediately (if any).
• QUICKSELECTKeeps the current selected entity type on Quick Select tool activation. 'Apply to current selection set' mode is automatically switched On if a selection set exists on Quick Select tool activation.
  SR66816
• RENDER MATERIALS The Transparency combo box was extended with a 'Cutout Map Inverted' option.
• RENDER MATERIALSImproved preview render speed for RedWay materials and improved lighting of material previews in the Material Browser.
  
• SECTIONPLANE Upon creation, sections now have their 'Clip Display' status On instead of the 'Live' status.
• SELECTIONMODESCan now be changed transparently, i.e. during execution of a command without aborting the command.
• SELECTSIMILARExtended to support true color (RGB).
  SR72007
• SHEET METAL
  • SMCONVERT The recognition of Wrong Bend features was made more accurate. A coincident-faces geometry is now detected.
  • SMDELETE The operation with Junction features has been improved.
  • SMFLANGEEDGE New option "Radius" has been added to allow adjusting the radius of a new bend directly in the command.
  • SMFLANGESPLITThe command now correctly updates existing features in complex cases.
  • SMFORM Added option to explode form feature to flanges and bends if possible.
  • SMRELIEFCREATEThe command is added to the quad menu.
  • SMRELIEFCREATEProvided a bend is selected, the bend relief(s) creation will be forced for this bend.
• SNAP TRACKINGImproved visual feedback during snap tracking: if snap tracking line direction is parallel to UCS axis, the color of the track is set to the color of corresponding axis (defined by COLORX, COLORY or COLORZ variables).
• STRUCTURE panelCan show nested block hierarchies. The Rules were extended with a Filter option.
• SWEEP command
  • Added the possibility to sweep from end point of the path in reverse direction.
  • Corrected alignment of profile respectively path in command SWEEP, to avoid redundant flips of the swept profile.
• TEMPLATE DRAWINGSChanged standard mleader style in all template drawings to set 'Right Attachment' type to 'Middle of top line'.
  SR50342
• TIPS
  • During pre-selection (hovering) of a polyline, mleader or associative array, a Tip is displayed to inform the user that the Ctrl key can be used to select subentities, and thus use the Quad to perform operations on those subentities.
  • Each Tip can now be individually configured using the new Tips Configuration dialog.
  • Tips sysvars "Hide Tips", "Show until dismissed", and "Always show tips" were removed and replaced with "On" and "Off".
  
  SR71742SR72509SR72196SR72797SR73303SR73454SR74096
• TOOLPALETTESMultiple items from toolpalettes can now be selected to have properties changed.
  SR63029
• TOOLPALETTESAdded support for macros in command tools.
  SR69806
• TRANSPARENT IMAGESTransparent raster images no longer produce opaque shadows using the entire image rectangle. Now the shadows take the transparent areas of the image into account. Example: an image of a person, in which the area outside the silhouette of the person is transparent, will now cast a shadow corresponding to the silhouette.
• UCSORTHOModified the default value to Off. Since the introduction of Dynamic UCS, UCSORTHO is less needed, instead it causes confusion.
• VIEW ROTATION CENTER POINT For real-time view rotation using the mouse, the center point of the view rotation is now derived from the entity found under the cursor instead of using the center point of the viewport. In case no entity is hovered by the cursor, the rotation center point is defined by the center of entities completely inside the viewport.
  
• VIEWBASEPROJECTIONTYPE setting was ignored when creating an isometric viewport. Third angle projection was always used.
• VIEWSWhen copying a view using the Drawing Explorer, the properties of the background used for the view are now also taken along.
• VIEWDETAIL, VIEWSECTION
  • New ribbon panel tools allow creating views of different types.
  • The command options have been simplified.
  • Types of created views such as Full, Offset or Circular, Rectangular are now controlled by top level command options.
  • Dedicated layer for hatches in section views.
  • Hatch angle is the same for projection of one solid and changes according to view section style for intersected or adjacent projections of different solids.
  • Hatch scale is now the same for all section views in Paper Space and it does not depend on the scale of the view.
  • Section projection depends on projection type (first or third angle).
• VIEWSECTIONSTYLE and VIEWDETAILSTYLE
  • Unmodified section identifiers are correctly updated after editing the Position setting of the correspondent section style in the Drawing Explorer.
  • The dialogs associated with the VIEWSECTIONSTYLE and VIEWDETAILSTYLE commands have been moved to the Drawing Explorer.
  • The commands have been changed to open the corresponding section of the Drawing Explorer.
  • Support for multiple styles per document has been added.
• XREF ATTACHMENTMultiple xref drawings can now be attached in one operation.
  SR40280SR41225SR62977
• ZOOM
  • Quad and selection preview are disabled during scroll zoom to avoid undesired interference.
    
  • Improved scroll zoom performance for (xref)drawings containing xlines and rays.
  • When scrolling the zoom wheel fast, one or more intermediate redraw operations are skipped, resulting in faster zoom navigation.
• ZOOM PERSPECTIVEImproved zoom experience in perspective views allowing to zoom in really close on the object positioned under the cursor.

Fixes

• 3D MODELLING Fixed crash in _DMPUSHPULL command.
  SR73559
• AUDIT End parameter (DXF42) of ellipses is replaced by 2PI during loading a DXF file if values of ellipse start and end parameters are equal to 0.0. Before this fix, such ellipses were discarded.
  SR70018
• BMINSERT Command incorrectly responded to the dynamic input when the Array option was used.
• -BHATCH "-BHATCH _Properties ? *" resulted in a hangup.
  SR75915
• COPYCLIP/PASTECLIP COPYCLIP/PASTECLIP could fail when using non-default UCS.
  SR75741
• DRAWING EXPLORER Fix crash in View Section Style.
  SR76064
• ETRANSMIT Data files for 3D online viewing were always generated, disobeying the related setting.
• FROM XYZ filter was undesirably applied when combined with FROM offset option.
  SR76160
• LOCALIZATION Corrected multiple issues for localized BricsCAD versions.
  SR75892SR76252SR74171SR75961SR76168
• MECHANICAL BROWSER Program crashed on incorrect filename entered when using the Replace context menu item.
• PEDIT Option to join lines to a polyline malfunctioned if UCS differs from WCS and polyline and lines lie in UCS XY plane.
  SR73748
• PRINT DIALOG When the PRINT dialog's virtual size is larger than the screen, automatically show a scroll bar so controls are kept in reach by the user.
  SR76455
• PUBLISH TO PDF Fields with CTAB value were not published correctly to multi-sheet PDF in some cases (depending on nesting, active layout).
  SR75856
• PUBLISH
  • '.plt' file extension undesirably was used instead of '.pdf' for publishing with Print As PDF.pc3
    SR76215
  • The command could fail when trying to publish in background which is currently not supported. The operation will always happen in foreground meanwhile.
    SR76264
• SHEET METAL
  • SMFLANGEEDGE Junction feature was not created in case of present adjacent feature of the same type.
  • SMFORM Explode operation could not be undone correctly.
• SHX Fonts Fixed a regression where shx fonts ended up with the wrong size when printing to PDF
  SR76264 SR76703 SR76379
• TOOLPALETTE Blocks on a tool palette, which have the 'Prompt for rotation' option set to NO, undesirably were aligned with the WCS, while they should be aligned to the current coordinate system instead.
  SR76516
• VIEWPORT In a locked viewport, when using pan/zoom during a command, it was possible to modify the locked view. Regression since V17.2
  SR75819
• WBLOCK Block names were not alphabetically sorted in WBLOCK dialog.
  SR74844

• ANNOTATIVE MTEXTPosition of an annotative mtext was wrong after changing the position and saving, closing and reopening the drawing.
  SR74864
• ANNOTATIVE SCALESWhen purging excessive scales from a corrupt drawing, a crash could occur.
  SR75701
• ATTRIBUTES
  • Fixed cases of undesired rotation of multi-line attributes.
  • The background mask settings of multi-line Attributes were not properly stored.
    SR75226
• BASEFILEImport User Profile was resetting BASEFILE and other vars, if that profile did not include a value for WSCURRENT.
  SR74763
• BMFORMOrphan component parameters might appear in case the command was applied to a geometry not linked to 3D constraints.
• BMINSERTThe rotation angle incorrectly accumulated when the Rotate option was used two or more times.
• BMUPDATE Update of a component in a user-provided assembly led to an unhandled exception.
  SR75149
• CIRCLEWhen the CIRCLE command was invoked from the toolbar, and a value had been entered for the radius in the dynamic input field, the dynamic input value was ignored in case the mouse was moved after entering the value, instead the cursor position was applied.
  SR47325SR70720
• COMPATIBILITYAutoCAD crashed during an attempt to read the silhouette lines of a 3dsolid that had been saved by BricsCAD.
  SR74649
• CVPORT A drawing file with overall paperspace viewport turned off reported CVPORT -1 and the PSPACE command was inoperable.
  SR75495
• DIALOGS Pressing Enter didn't close dialogs with OK on Mac.
  SR68149
• DIMBREAKDimensions with duplicate breaks caused COPYCLIP and SAVE commands to fail. The Dimbreak command now prevents multiple addition of the same breaking entity.
  SR75315
• DIMENSION STYLE Combo controls in the dimension style grid now work correctly
  SR73575
• -DIMSTYLEThe 'V' option of the -DIMSTYLE command ('Variables') undesirably triggered the restore prompt.
• DISPLAY
  • Display failed for a number of user-provided lofted 3dSolids.
    SR70411SR71983
  • Holding the Alt key by itself could unexpectedly trigger Alt-Home view change.
• DISPSILHA hang-up could occur upon switching layouts in case DISPSILH was on and the drawing had 3d objects with very big coordinates.
  SR75463
• EXPORTPDFExport to pdf failed for a very narrow hatch boundary with custom hatch pattern.
  SR74158
• EXTREME COORDINATESIf a drawing contained entities with huge X/Y coordinates and very small Z coordinates (but not exactly 0), entities could fail to be displayed.
  SR74961
• JPEG2Use meter as the default cell unit type in case the cell unit type of a jpeg2 image file is unknown.
  SR75572
• LAYOUTIt was not possible to rename a layout to the same name with different uppercase/lowercase characters.
  SR75055SR75200
• LOCALIZATION
  • Fixed translation issues with error messages and ViewDetailStyle dialog.
    SR75273
  • Some texts could not be translated or contained typo's.
    SR74887SR74947SR75125
  • False/True options in 'Physical Materials' dialog failed to be translated.
    SR75781
  • The default option of the VIEWSECTION and PLOT commands was not translatable.
    SR74171 SR75294
• MATERIALMAPCrash occurred during command execution.
  
• MTEXT_IME OS native IME was not fully functional for the in-place MTEXT editor.
  SR68887
• OFFSETOffset of polyline segments with bulge smaller than 0.002 drawing units was incorrect.
  SR74612
• PDFLAYER The layers in a PDF underlay could not be turned On/Off using the PDFLAYER command.
  SR75507
• PLINECACHEWith PLINECACHE enabled, opening a drawing file containing proxy objects could result in a crash.
  SR75207
• PLOT STYLE
  • After creating a new plot style table in the PRINT dialog, the new style was created but shown as "missing".
    SR75354
  • The background mask frame of multi-line text failed to obey the plot style settings.
    SR69782
• PRINTA crash could occur when printing or print-previewing raster images with clipped boundaries.
  SR74492SR75804
• PROMPTOPTIONFORMATThe shortcut is now appended as well in the prompt menu in case the option is set to value 3 (display shortcut between brackets).
  SR75236
• PUBLISH
  • After loading a .dsd file, the 'Publish to' choice was no longer updated.
  • An incorrect "file is read-only" warning could appear when publishing unopened drawings. The issue only happened if "Publish in background" was unchecked.
    SR75277
• REFCLOSEThe Refclose command added duplicated overlay items in xref drawings.
  SR70235
• RENAMEThe dot '.' is no longer interpreted as a wildcard but instead as a plain character - it introduced more difficulties than advantages.
  SR74909
• RIBBONThe ribbon split button failed to display its image if it was not built-in but coming from a custom resource.
  SR74790SR75068SR75107
• SCALE CALIBRATIONResolved a clipping issue when scale calibration is used for a printer on UNIX
  SR70809
• SHEET METALSMBENDCREATE command could lead to a critical error.
  SR74837
• SWEEPA user-provided sample sweep case failed since V17.
  SR74433
• TABLESEvaluation of a formula in a table led to a crash.
  SR75366
• TEMPLATE DRAWINGSUndesired overall viewport were removed from the paper space layouts in Default-mm.dwt and Mechanical-metric.dwt. It led to failure of automatic viewport creation.
• TOOLBARS Add a context menu with predefined toolbar actions to make working with toolbars easier: move one row up/down, move on column left/right, dock to top/bottom, etc. A notable action is Wrap: rearrange invisible or partly visible toolbars on new rows so they become fully accessible.
  SR62902 SR74205
• VIEWPORTViewport clip could be ignored for clip regions with islands.
  SR73032
• VIEW SECTION STYLESelecting the 'Solid' hatch pattern in the View Section style triggered an error dialog box.
• VISUAL STYLESAdded '2D Wireframe' option to the Visual Styles submenu of the View menu.
  SR74232
• WMSParsing of the parameters of a specific WMS server failed.
  SR75788